Structural Fire Damage Cleaning in Grenada, MS
The drywall is gone, and now you are staring at blackened studs, scorched joists and a charred roof deck. The question is which members can be cleaned, which need a sister, and which have to come out. Unify Fire Solutions connects you with independent, licensed and insured contractors in Grenada who clean the framing, masonry and steel itself.
- Soda blasting, dry ice blasting and wire brushing
- Every stud and joist probed for char depth
- Cleaned wood encapsulated against lingering odor
Why the Bare Structure Needs Its Own Crew
Close up the walls over dirty framing and the smoke odor bleeds right back through the new finish. Cleaning the structure is the step that decides whether the rebuild smells like a new house or a campfire.
Licensed & Insured Independent Pros
Each contractor on our referral list is an independent, licensed and insured local company. Check the paperwork yourself and ask if their process lines up with IICRC S700.
Upfront Written Estimates
Blasting is priced by surface area, media and access, and attics and crawlspaces cost more to reach. Get a written, itemized estimate in hand before any blasting begins.
Rapid Local Dispatch
Day or night, a dispatcher picks up and starts looking for a structural cleaning crew right away. Timing depends on which crews near Grenada are free, and it is often the same day.
Blasting Rigs and Probing Tools
This trade runs on gear most remodelers do not own: soda blast pots, dry ice blasters, tow-behind compressors, HEPA vacuums, air scrubbers and an awl for probing char.
Do not climb into a burned attic or walk a scorched roof deck to look for yourself. Weakened joists and burned-through sheathing can give way without warning, and exposed wiring may still be live. Wait for the contractor to check that the structure is safe, and keep people off floors that sit over a burned crawlspace or basement.
Cleaning the Building From the Roof Deck Down
Furniture and debris are a separate job. This page is about the framing, masonry and steel that actually carry the load.
Char Depth Probing and Member Decisions
Pressing an awl into the blackened wood shows how deep the char goes; a shallow crust over firm wood usually means it can be cleaned. When the char cuts deep into a joist or a truss web, the member gets sistered or swapped out.
- Members marked clean, sister or replace
- Structural engineer called in for questionable beams, trusses and headers
- Photos of each marked member for the claim
Soda Blasting
Sodium bicarbonate is softer than wood, so it strips soot and light char off studs, joists and roof decking without gouging the grain. It leaves a fine white dust and some residue, so containment and a thorough HEPA vacuum afterward are part of the job.
Dry Ice Blasting
Dry ice pellets hit the surface and turn straight into gas, so there is no media left behind to sweep up. It suits cramped attics and areas around wiring, but it runs louder and pricier than soda.
- Hearing protection and ventilation required
- Good choice when residue would be a problem
Wire Brushing and Sanding
For a few blackened studs or a small closet fire, wire brushes, sanding discs and a HEPA-shrouded grinder may be all it takes. Hand work is slower but sensible where a blast rig would be too much.
Brick, Block, Concrete and Steel Beams
Porous brick, block and concrete trap soot deep in the surface, so crews use alkaline detergents, scrub brushes or blast media to lift it. Steel beams get cleaned and inspected for any heat warping, with doubts sent to the engineer.
Encapsulation and Attic Insulation Removal
Cleaned framing gets a coat of shellac-based or specialty encapsulant to lock in any odor left deep in the wood. Attic jobs start by vacuuming out the smoky blown-in or batt insulation so the rafters and roof deck can be reached.
Crawlspaces get the same treatment on a smaller, dirtier scale: floor joists, sill plates and the underside of the subfloor are probed, blasted where needed and sealed. Expect a vapor barrier to be pulled and replaced if smoke or hose water soaked it.
Ask your contractor which method they recommend for each area and why. It is common to see soda in open walls, dry ice in the attic and hand sanding near the electrical panel on the same job.
Containment matters here, since blast media and loosened soot travel anywhere the air moves. The crew hangs poly over doorways, masks off the HVAC returns and runs air scrubbers under negative pressure while they work. Ask how they will protect finished rooms and windows that were not damaged.
Looking at Blackened Studs and Rafters?
Ring the dispatch line and we start finding a structural cleaning crew near Grenada. It costs nothing to call.
Call +1-833-336-1630The Path From Charred Framing to Sealed Wood
- 1
Phone the Dispatcher
Describe what is exposed: open stud walls, an attic, a crawlspace, block or steel. Mention if a roofer, engineer or adjuster has already been out.
- 2
Mobile Crew on Site
The contractor arrives with a compressor, blasting equipment and containment materials. First they confirm the roof deck and floors will hold weight and that the exposed circuits are dead.
- 3
Probe, Mark and Quote
Every exposed member gets probed with an awl and marked clean, sister or replace, and anything borderline goes to a structural engineer. A written, itemized quote covering area, blast method, encapsulant and attic insulation comes before any work starts.
- 4
Blasting, Sealing and Walkthrough
After blasting and HEPA cleanup, the framing gets its sealer coat, and you walk the bare structure with the crew lead. Do a sniff test on a warm afternoon, and ask for photos of every marked member before the rebuild closes the walls.
Notes From People We Connected
After the attic fire, the rafters were black and the blown-in insulation was a wet mess. The crew pulled the insulation, dry ice blasted the rafters and rolled sealer on everything. An engineer looked at two deeply charred rafters and they were sistered instead of torn out.
I assumed every black stud in the hallway had to be replaced. The crew lead probed each one with an awl and showed me that most were just surface char. They soda blasted and sealed them, and only three were swapped.
The fire in our lower level left the block walls and the steel beam coated in soot. The contractor cleaned the block and the beam, then had an engineer check the steel for warping. The basement smells normal again, even closed up.
Common Questions About Cleaning Charred Framing
How do crews decide if a charred stud can stay?
The test is simple: they probe it. An awl or screwdriver pushed into the black surface shows how deep the char goes, and wood that is firm just under a thin crust can usually be blasted and sealed. Members with deep char, splitting or a lost cross section get sistered or replaced, and anything structural in doubt goes to a licensed structural engineer.
What is the difference between soda blasting and dry ice blasting?
Soda media is mild on the grain and helps with odor, though it leaves a white dust that needs a full HEPA cleanup. Dry ice pellets vanish on impact, so cleanup is easier and it works well around wiring, but it is louder and usually costs more. Many crews use both on the same house.
Why seal the framing if it has already been cleaned?
Wood is porous, and smoke molecules sit deep in the grain where no blasting can reach. An encapsulating sealer traps what is left so the odor does not seep back through the finished walls. Sealing dirty wood does not work, so the cleaning has to come first.
Does the attic insulation have to come out after a fire?
If smoke reached the attic, almost always yes. Blown-in and batt insulation trap smoke and soot like a filter, and many get soaked by hose water too. Crews vacuum it out with a truck-mounted or portable insulation vac so the rafters and decking can be inspected and cleaned before new insulation goes in.
Can soot be cleaned off brick and concrete block?
Most of the time, but brick and block hold soot in their pores and need more than a wipe. Expect alkaline detergents and scrub brushes for light staining and media blasting for thick deposits. Heat-cracked or spalled block and brick should be looked at by an engineer or mason.
Do I need a structural engineer for fire-damaged framing?
You may not on a small job, but any doubtful load-bearing member calls for one. An engineer's report on trusses, headers, beams, steel and badly charred joists protects you and supports the claim. Your local building department may also require one before the walls close.
Charred Framing Cleaning Across Grenada and Beyond
Our dispatch line covers Grenada and the nearby communities around it, from older homes with plaster and solid-sawn joists to newer builds with engineered trusses. Attics, crawlspaces, basements, garages and small commercial buildings are all in scope.
- Attic fires
- Electrical fires
- Furnace puff-backs
- Chimney fires
- Lightning strikes
- Neighbor's fire spread
Should the first contractor not suit you, ring us again and we will connect you with a different one. Do not let the rebuild close walls over dirty framing.
